WHEN TO CALL AN EMERGENCY PLUMBER?

It can be difficult to tell if a leak is a serious emergency or something that can wait until normal business hours. You may react instinctively and rush to the phone, rather than calmly assessing the situation. Let’s not lose our cool. These are some questions that you should ask before calling an emergency plumber near to you. This will help you avoid overpaying and allow you to get back to sleep.

1. Are You Requiring to Use the Affected Plumbing Now?

An emergency call is necessary for a flooding basement. But what about a clogged toilet or sink? They might be able to wait until the morning to schedule a plumber appointment. If this happens, let your family know that they will not be using the fixture again until further notice. To avoid forgetfulness at night, tape a note to the wall or completely block the room.

2. Is it possible to turn the fixture off?

It’s not considered a plumbing emergency if you can fix the leakage at the sink. The shut-off valve is located under the sink or behind your toilet. For larger problems, you might need to shut off the main water supply to your house. You will find the main shutoff valve near the water meters on the street side of your house.

You might be able stop the leak for a few hours if the leak is less severe than a trickle.

3. What’s the weather like?

The weather can play a significant role in whether you require plumbing services immediately. It’s dangerous to not have water at your disposal if it is a hot summer day. Call a plumber in Myrtle Beach if the temperature outside drops below 32 degrees Fahrenheit, and your water heater struggles to turn on.

4. Is it possible to do more damage if the problem is left unattended?

To stop a slow leak, you could use buckets to collect water and stuff rags into the pipes. Your leak becomes more serious if one bucket doesn’t suffice to get you through the night. A significant leakage can cause damage to your floor, ceiling, walls, and adjoining walls. It’s time for you to call 911 if the water flow isn’t stopped or the water can cause significant damage.

5. Is it Your Responsibility to Fix the Problem

Sometimes, you may not be able to fix the emergency even if it was urgent. Your water company might offer to send a plumber to fix a problem with your main water line, the sewer main or a blocked sewer. Before calling your plumber in Myrtle Beach, you might try them. You might get city employees to fix problems with your city water supply. City employees may fix problems with city water supplies for free, unless you have to pay for repairs to the main water line.

Common Plumbing Emergencies

Broken pipes: Turn off the water supply to a pipe that is spraying water. Move furniture out of the area.

Leakage or failure of a water heater: Call for assistance if the tank is making strange or unusual sounds, leaking, or making a foul-smelling odor. Water heater failures can cause expensive damage quickly.

Other major leaks include Toilet overflows, washing machine hoses and gas line leaks.

Sewer system backups. If you notice a bubbling toilet or water in your shower after flushing the toilet, it could be a sign of sewer system backups. Sewer gases can seep into a basement if it smells like rotten eggs.

What happens if you call an emergency plumber?

It’s a stressful situation. Keep calm and try to mitigate the emergency plumbing situation. Look for the shutoff valve on the fixture. Next, assess the situation and call a trusted professional emergency plumber in Myrtle Beach if necessary.

Professional plumbing repairs can still be expensive. This is especially true if you don’t have a reliable plumbing company on-call. If time permits, call three companies to get an estimate. This will help you determine a fair price.

Even in an emergency, it is important to ask questions. Before you agree to emergency plumbing service, tell the company about the problem and request a cost estimate. This includes the cost of regular service as well as any additional fees for night- or weekend calls.

While the cost of a plumbing problem might go up once the contractor has assessed the issue, it is important to be cautious of companies that refuse to provide an estimate over the telephone, even if you have provided sufficient details.

What is the Average Cost of an Emergency Plumber?

For a holiday, weekend or late-night plumbing repair, expect to pay less than a half hour. For emergency visits, companies might charge a flat fee between $100 and $350. These fees could be added to the usual $70-$400 hourly rate.

The plumbing contractor might be able to manage the problem in the evening and then return with the parts needed later. You might be charged an additional visit and the hourly rate. These details should be discussed with you when selecting a contractor.

Call Blue Ribbon Plumbing LLC now if you need the help of a professional plumber.

Like our Facebook page for more great info about plumbing services.

Blue Ribbon Plumbing LLC
4201 Carolina Exchange Drive Suite 202
Myrtle Beach, SC 29579
(843) 267-9733
https://www.blueribbonplumbingmb.com/

TANKLESS HOT WATER HEATER

Tankless water heaters are a popular choice if you’re looking for a new heating system. These systems are ideal for replacing traditional water heating systems for commercial plumbing uses such as hotels, apartments, schools, or any other business that has high water consumption.

There are many benefits to tankless water heaters. Let’s look at them:

It is a long-lasting system that requires little maintenance

Did you know that tankless water heaters are durable and can last up to 20 years, while only needing repairs every 15 years? This means that you can install a tankless heater and have it last for almost 20 years with minimal maintenance. This can save you thousands of dollars on energy and maintenance costs if your apartment or hotel is a complex.

They take up less space

A 100-gallon commercial water heater will require a lot of space on your property. Storage tanks and water heaters take up more space. Tankless water heaters, on the other hand, take up much less space as they don’t require storage tanks. They heat only when it is needed and don’t need large storage tanks. The water heater heats up in seconds when someone presses the button to get hot water. Memphis is growing, so there is not much room for large buildings. Modern buildings in Memphis have been specifically designed to house tankless water heaters, and are limited in space.

Flooding risk is greatly reduced

The possibility of water flooding a property due to tankless water heaters is much lower because they don’t require storage tanks. Tenants can forget to turn off the water in a residential unit that has a traditional tank. This could lead to water overflowing the tanks and flooding the property.

Tankless water heaters are able to heat water as quickly as it needs without waiting, so flooding is not a concern.

Flooding is only possible through water leaks. However, tankless water heaters can last for about 20 years, so you don’t have to worry about any water leaks.

Waste less water

Wistfulness is decreased because water is heated only as necessary in tankless heaters. Tankless water heaters are very safe. Tankless water heaters heat water as long as the person is using it. They will then stop heating when they are turned off. This saves both water and energy. A tankless water heater is a viable option for eco-conscious consumers.

It’s time for property owners to switch to tankless water heaters if they still use traditional water heaters.

Are You Ready to Install A Tankless Water Heater?

Contact Choate’s Today to learn more about tankless water heaters and how they can help your business.

Our residential plumbing professionals are ready to answer all your questions and explain all the installation steps before we start the project. Call us at 843-267-9733 24/7 for personalized, professional plumbing services.

Blue Ribbon Plumbing LLC
Myrtle Beach, SC 29579
843-267-9733
https://blueribbonplumbingmb.com

PLUMBER TIPS: WHAT TO DO IF YOU HAVE TOILET PROBLEMS

Many homeowners consider their bathroom to be the most frequently used room in their house. It shouldn’t surprise that sometimes the toilet will break down. Broken toilets can be a major problem for the entire household. When that happens, you may need the help of a plumber.

Plumber Tips: Fixing A Broken Toilet

You want to fix a toilet that is broken as soon as possible. Although unclogging a toilet can be done quickly, it is not always possible to fix every problem.

There are many moving parts in the tank, so there could be several issues. There may be constantly running water or unusual noises. You might have water accumulating at your toilet’s base.

What problems are beyond the scope of a DIY project? These are just a few examples of toilet problems that require a professional plumbing contractor.

Water near the Toilet Base

Are you seeing water around your toilet’s base? Try to wipe the area clean with a towel. You can leave a few more paper towels around the base for a couple of hours. You may find that the wax seal around your toilet base is worn.

You will need to hire a plumber in Myrtle Beach to fix the wax ring.

If your paper towels don’t get wet upon return, you should check the connection between the tank supply and the hose supply. You can use the same method with the paper towels to check the area for leaks.

Any drips should be checked at each end of the supply hose as well as a flush valve. If you discover a leak, it may be necessary to replace the supply line. Leakage at the tank’s bottom means that you will need to replace the flush valve.

Slow Tank Fill

Toilet tanks that take a long to fill could be due to a leaking flapper or broken flush valve. To flush the toilet, remove the tank lid. You need to replace the flush valve if you notice the flush valve sticking, or if you hear water trickling from the toilet.

Water may seep through the flapper. The leak could cause water to seep through the flapper, making it more difficult to fill your tank. Repairing the flapper is the only way to fix a leaky seal. These parts can be replaced by a plumber.

Irregular Running water

Leakage in gravity-flow toilets could cause intermittent running water. Make sure your toilet tank ball is centered on your valve seal. You need to replace your valve if it falls off-center or does not connect properly. A plumber in Myrtle Beach will be able to fix the problem by removing the tank ball from the valve and installing the new valve.

Continuous Running Water

Water may run aground if the chain is in your tank. Check that the chain is strong enough to seal the hole in the tank’s bottom. If it isn’t, the flapper won’t be able to drop far enough to close the hole. Most chain problems don’t need a plumbing contractor. The length of the chain can be adjusted by simply unlatching or increasing the clip.

You may hear a faint drip of water. This could be the sound of the ball cock. The ball is connected to a float mounting to close the valve when the water level reaches the desired level.

The seal between the ball mount arm and the float mount arm can wear and cause the tank water to leak. You will need to have a plumber replace the rubber diaphragm.

You might just have dirt in the seal. You can remove the sediment by yourself. Just unscrew the screws to clean up the seal. Get rid of any residue.

A plumber is the best option when it comes to toilet repair. You can have them come out and fix it or guide you through how to fix it. Professional guidance can save you time and money.

Like our Facebook page for more great info about plumbing services.

Call Blue Ribbon Plumbing LLC now if you need the help of a professional plumbing contractor.

Blue Ribbon Plumbing LLC
4201 Carolina Exchange Drive Suite 202
Myrtle Beach, SC 29579
(843) 267-9733
https://www.blueribbonplumbingmb.com/

DRAIN CLEANING GUIDE HOMEOWNERS NEED TO KNOW

Aside from filthy gutter on your roof or weeds in the garden, the next most typical problem in a home is clogged drains. Most homeowners will try to solve this problem on their own. Nevertheless, while it’s definitely possible, it is necessary to understand that you might, in fact, do more damage to your pipes without you knowing it. In this blog, we will share with you some tips to help with your drain cleaning problem.

Drain Cleaning Tips

All you need might be regular tools you have at home

Plumbing professionals have a large choice of the most recent cutting-edge tools at their disposal. However, a typical homeowner may only need tools regularly available at home. If you have a toilet plunger, you can use it to unblock a persistent clogged shower or tub drain. Also, if the blockage is shallow, another drain cleaning solution is using a long screwdriver to solve the problem. But if you do not have these tools, you can buy a little drain snake or auger from your local home improvement store.

Using chemical drain cleaners is dangerous

While you have seen countless TV commercials claiming their chemical liquid drain cleaner works, maybe too good to be true. What chemical drain cleaners do is gnaw at the obstruction, ultimately triggering it to remove and flush away. Nevertheless, what most homeowners do not know is that these chemicals wear away anything they come in contact with, even your pipelines. If at all possible, plumbers recommend avoiding using it or you might end up with a bigger drain cleaning problem

Try flushing the clogged drain with hot water

Think it or not, a great flush with hot water can, in fact, meltdown a few of the sticky compounds that are stuck in your pipeline. The very first thing you need to attempt is to run the hottest water possible from your faucet and down the drain to clear the obstruction the natural method. Most often, homeowners are surprised at how this instantly works. But homeowners should understand that this step will not totally solve their clogged drain issue. It is still recommended to call Blue Ribbon Plumbing to solve this issue. However the easy Do It Yourself technique of running hot water down the drain might resolve the issue quicker and easier than you thought possible.

Like our Facebook page for more great info about plumbing services.

Call Blue Ribbon Plumbing if you need residential and commercial plumbing services.

Blue Ribbon Plumbing LLC
4201 Carolina Exchange Drive Suite 202
Myrtle Beach, SC 29579
(843) 267-9733
https://www.blueribbonplumbingmb.com/

PLUMBING TIPS: FIXING SLOW TOILET FLUSHING

While there are many systems that can improve your comfort and convenience in your home, the most important is the functioning toilet. It can be embarrassing for guests to see your toilet when it doesn’t flush correctly, leading to partial flushes or leftover waste. An experienced DIYer can often fix a slow-flushing toilet. However, it all depends on the problem. Here are some plumbing tips you need to know.

A toilet that flushes slowly or insufficiently can have many causes. It is important to determine the root cause of the problem before it can be fixed. Low water levels, partially blocked drains, mineral buildup, defective flappers, and blocked drain vents are all common causes for slow-flushing toilets. This article will provide a detailed breakdown of the causes and possible solutions to your problem.

Plumbing Tips: Fixing some toilet problems yourself

Low water level

Low water levels are one of the main reasons toilets have trouble flushing. The tank may not have enough water to flush the toilet. This will cause the toilet’s flushing power to be reduced as there is only a small amount of force entering the toilet.

A full tank generating enough pressure to flow into the toilet bowl is sufficient to force the contents into the drain. You will likely have some waste that won’t be flushed if there isn’t enough water. Wait for the tank to refill before you flush again.

You can fix this issue by changing the level in the tank’s toilet float. The toilet float is placed on top of the water surface and turns off the fill valve when it reaches a certain level.

To increase the toilet’s flushing power, adjust the toilet float to allow more water to fill the tank before the fill valve turns off.

Partially Clogged Drain

Clogged toilets are easy to spot. Most people can use a plunger or a wrench to remove the blockage. However, a partially blocked toilet may be harder to find because it will still flush but with a significantly reduced efficacy. There are many ways to clear a partially blocked drain and restore your toilet’s flushing power.

The first thing to do is to plunge the toilet. The plunger will usually clear partial or complete clogs. However, if that fails, it is worth looking into a drain snake. If you have trouble clearing the blockage, such as with children’s toys, floss, or wipes, it’s time to call a plumber.

Mineral build-up

The jet holes on the underside and rim of the toilet bowl allow water to flow from the tank into its bowl. These holes are small and can get clogged, or partially blocked due to their small size. This reduces the flush force.

Minerals like calcium and magnesium can build up in the jet holes and block the flow of water if you live in an area with hard water.

To help remove the buildup of minerals, use distilled white vinegar and stiff-bristle toilet brushes. This will restore the toilet’s flushing power. To prevent this from happening again, it’s a good idea for you to install a water softener.

Flapper/flush valve defective

Sometimes, the problem with slow flushing toilets can be traced back at the flapper or flush valve assembly. These parts are located in the toilet tank. They release the water from the tank to the bowl. The flush valve assembly is composed of an overflow tube and a lever, chain, flapper, and the opening for the flush valve in the tank’s base.

The flapper, a rubber plug or ball that blocks access to the toilet bowl’s opening, is usually located on one side of overflow tube. The flapper is activated by pressing the button or lever on the toilet. This releases the water from the tank and lets it out into the bowl.

You can also find flush valves that are directly above the opening of your flush valve. These flush valves use a flush seat to plug the opening of the toilet bowl, instead of using a flapper. The flush valve seat lifts when the toilet is flushed. This allows the water from the tank into the bowl.

If the flapper or flush valve is damaged, the water flow into the toilet bowl could be reduced. This can cause a slower flushing toilet by reducing the flow rate. This problem can be fixed by inspecting the flush valve assembly. This can sometimes happen when the chain gets stuck or trapped. You may be able fix it fairly easily.

If the problem continues, it is possible to replace the entire flush valve assembly. It’s not a difficult repair. However, if the problem persists, you may need to contact a professional plumber in Myrtle Beach.

Ventilation of blocked drains

Many people are unaware that the plumbing drain lines that allow wastewater to flow from the home to the municipal sewer system or septic system are connected with vents. Vents are usually located on the roof. This allows gasses to escape from the pipes instead of building up and causing unpleasant odours throughout the house. They don’t only help with smell, but also release hazardous gas to the exterior.

Occupied vent lines can decrease the flushing power of toilets and should be removed immediately to avoid further problems with the wastewater system. It can be difficult to clear these vents because you have to climb up onto the roof.

This can be especially difficult if you don’t know what to look for on the roof. To clear your vents, it is a good idea to hire a professional plumber.

Like our Facebook page for more great info about plumbing services.

Call Blue Ribbon Plumbing LLC now if you need the help of a professional plumber in Myrtle Beach.

Blue Ribbon Plumbing LLC
4201 Carolina Exchange Drive Suite 202
Myrtle Beach, SC 29579
(843) 267-9733
https://www.blueribbonplumbingmb.com/